ASTM D885 PDF
ASTM D – Air Permeability of Textile Fabrics . Reference: ASTM D – Standard Test Methods for Tire Cords, Tire Cord Fabrics, and Industrial Filament . ASTM D/DM: Standard Test Methods for Tire Cords, Tire Cord Fabrics, and Industrial Filament Yarns Made from Manufactured Organic-Base Fibers. This standard is issued under the fixed designation D ; the 1 These test methods are under the jurisdiction of ASTM Committee D13 on.
|Published (Last):||4 October 2010|
|PDF File Size:||1.16 Mb|
|ePub File Size:||15.58 Mb|
|Price:||Free* [*Free Regsitration Required]|
Email addresses can only contain letters, numbers and the following special characters: Link to Active This link will always route to the current Active version of the standard. CP Rated capacity 5 kN kgf, 1, lbf Suitable for testing a wide range of tire cords, braided wire, tow and mono-filements. Count of Tire Cord Fabric. Discover simpler and smarter testing with features such as pre-loaded test methods, QuickTest in seconds, enhanced data exporting: SI units is the technically correct name for the system of metric units known as the International System of Units.
As a minimum, test samples should be used that are as homogeneous as possible, that sstm drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Incorporates a grooved channel for specimen guidance.
ASTM D885 Tire Cord Tensile Test
Concrete, Asphalt and Rock. Significance and Use, Tensile Properties. Elongation at Break of Conditioned Yarns and Cords.
Email addresses must contain the symbol. Check this box to receive pertinent commercial email from Instron ashm on products, upcoming events, and more! Tensile Properties of Yarns and Cords.
ASTM D885 – Tensile Properties of Tire Cords, Tire Cord Fabrics, and Industrial Filament Yarns
They may be applied to similar yarns and cords used for reinforcing other rubber goods and for other industrial applications. It is recommended that any program of acceptance testing be preceded by an interlaboratory check in the laboratory of the purchaser and the laboratory of the supplier on replicate specimens of the materials to be tested for each property or properties to be evaluated.
They may be applied to similar yarns and cords used for reinforcing other rubber goods and for other industrial applications.
Bluehill Universal Brochure Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience. Width of Tire Cord Fabric. The values stated in each system may not be exact equivalents; therefore, each system shall wstm used independently of the other. Instron pneumatic tire cord grips are designed specifically for testing high strength tire cord, and are able to grip securely while maintaining high throughput It is important to review ASTM D to fully understand the test setup, procedure, and asttm requirements.
Specimen gripping Instron’s Solution: Adhesion of Cord to Elastomers. The values stated in either acceptable metric units or d858 units shall be regarded separately as standard. Twist in Yarns and Cords. Bibliography of Tire Cord Test Methods. Onsite Training At Your Facility.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Users of previous versions of software such as Bluehill 2 and Bluehill 3 can easily upgrade to the newest version of Bluehill. Link to Active This link will always route to the current Active version of the standard.
ASTM D Industrial Filament Yarns Made from Manufactured Organic-Based Fibers – Instron
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Properties of Tire Cord Fabric. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of asm limitations prior to use.
Historical Version s – view previous versions of standard Translated Version s: The result of this test is a determination of tensile strength of the cord being tested. Combining values from the two systems may result in non-conformance with the standard. Glossary of Materials Testing Terms. The test results ast, the two laboratories should be compared using a statistical test for unpaired data, asmt a probability level chosen prior to the testing series.
This standard details the testing of fibers and cords made specifically for use in the manufacture of pneumatic tires. They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator.