GRAPHTEC FC8000 MANUAL PDF
Vinyl Cutter Download Graphtec FC, Vinyl Cutter Machine Download Software Installation & Operation Manual in pdf ( MB) > Download Now. Manually Adjusting the FC ARMS Sensor Level for Glossy Media and Glossy Laminated Prints. When using some glossy media or when using glossy. View and Download GRAPHTEC FC Series user manual online. Cutting Pro . FC Series Plotter pdf manual download.
|Published (Last):||7 August 2011|
|PDF File Size:||14.1 Mb|
|ePub File Size:||15.37 Mb|
|Price:||Free* [*Free Regsitration Required]|
GRAPHTEC FC SERIES USER MANUAL Pdf Download.
Replacing Cutter Blade 12 – Replacing Cutter Blade Replace the cutter blade by referring to the structure diagram of Supplement the cutter pen. Unplug the power cord from the socket Prohibited Digits of settings can be changed by pressing the [FAST] key. Tool 1 will use the tool attached to the backward This setting is maintained even if the power is of the tool holder for half cuttingtool 2 will use the tool attached turned off.
Page – Adjusting for the Registration Mark Scan W Cross cut function cannot be used when the push roller sensor is disabled.
Media stocker Socket head cap screw Media stocker Mount the media stockers so that each one protrudes directly above the longer of the two base assembly lengths.
How to Improve Weedability We recommend that you observe the following points to improve the weedability of color marking film. The reply will be when set toand when set to Expanded effective cutting area In case of ARMS 4 or before, the cutting area is up to the area enclosed by the registration mark.
Preface In addition to cutting marking film and other media, an FC series plotter can also be used as a pen plotter. Cutting data in the buffer memory gc8000 be cleared. For front loading For rear loading Joint Cloth basket Attaching a Tool When mounting the tool in the tool holder, push the tool all the way into the holder until its flange contacts the upper part of the holder and then tighten the screw firmly. Checking the Contents Check that all of the standard accessories shown below are present.
Make sure that the tool bracket is engaged on the tool’s maanual, and then tighten the screw. The origin point can be set at any location. Operation Easily pull the bracket on the pen station forward and attach the plotting pen. Hold-down Force Assignments Hold-down Force Assignments Use the Strong or Medium setting for the push rollers used to hold down the edges of the media. Settings of Controls from Co Following items are displayed in the default screen.
Graphtec Manuals and Drivers – SignWarehouse Product Support
CAUTION When cutting maunal intensity reflective media The backing sheet used for the high intensity reflective media is very soft, so it will need a reinforcement.
But if there are many registration marks, it will take longer to detect, and the area that can be cut becomes smaller. There are 8 different patterns of perforated lines set as 0 to 7, and the ratio of cut and uncut part differs in each tool is raised or the force is decreased for following length every 8 mm of the cut.
See “Automatically Adjust” P. It also describes the settings of the plotter, confrming the cutting data, and method to create test patterns. The axis alignment can be performed using by printed industry standard crop mark for shear.
Page 9 How to Use Control Panel In case of using the Graphtec software, reversed color mark can be easily created. Coordinate value displayed here is the distance to the tool carriage from the origin point.
Page Press the  key RSC. This menu is not displayed on standard Operation equipment. Reinforce by affixing a media on the back side of the backing sheet, where the grit roller will be.
GRAPHTEC FC8000 Series User Manual
It indicates the current pen position, and is used for fine adjustment The loupe is mounted in the tool holder. Supplement Tool carriage will move away. Media stocker Socket head cap screw Media stocker U sed to turn the plotter on and off. Set the X value measured in step 9.
It cannot be retrofitted. Be sure to observe all the cautions on the label. Prohibited Prohibited Provide sufficient space around the plotter so that When using indoor lighting such as fluorescent it does not strike any objects in its vicinity during or other electrical lamps, provide a distance of at cutting.
Graphtec Manuals and Drivers
Adjustment of Offset Check the corners of the triangles and rectangles. It is appropriate fc800 cutting multiple numbers of stickers or similar. It makes it easier to confirm the cutting results if you perform this operation after the cutting is completed.
Caution Label is located on the top cover.
If any accessory is missing, contact your sales representative or the nearest Graphtec dealer. All the tool condition that is received from the computer will be ignored, and only the setting and change of the tool condition from the control panel amnual accepted when MANUAL is selected. It will give error or malfunction when it has made mistake.
Hold-down Force Assignments Use the Strong or Medium setting for the push rollers used to hold down the edges of the media. Supplement See “Settings of Controls from Computer” There are 2 types of sorting, the area sort and the tool sort. Push roller hold-down force switching lever Setting Regarding Interface This chapter describes setting regarding interface.
Sensor is adjusted to scan the registration mark written in black lines on white background.